Do you know any forklift operation skills?
Time of publication：2023-05-30
Forklift skills
1. Before starting, observe the surrounding conditions of the forklift (for vehicles with air pressure or braking, the reading of the braking air pressure gauge must reach the specified value before starting), and whistle for starting after confirming that it is safe
2. Before driving, check the drivers license, drivers license and other documents required for driving. Driving without a license, driving without a license or driving without a license is strictly prohibited
3. Forklift drivers in the plant must strictly comply with the on-site traffic safety management standards and safety production specifications
4. Check the technical condition of each vehicle department according to the specified items and standards to make the forklift in good condition
5. Do not lift the fork too high when driving in the factory. When entering or leaving the operation site or driving, pay attention to whether there are obstacles in the air. Sudden braking and sharp turning prohibited
6. When the forklift is driving in the factory, the height from the fork bottom to the ground shall be kept at 300~400mm, and the gantry must tilt backward
7. Unless under special circumstances, the foot brake shall not be used when the forklift in the plant travels more than 7 ° and goes uphill and downhill at a speed higher than first gear 8. During loading and unloading, the forklift must be braked by the brake. If a crane is used to load and unload workpieces, the driver must leave the cab
9. After the forklift stops in the factory, it is forbidden to hang the goods in the air. After unloading, lower the lifting frame before driving
10. When the forklift is working in the factory, it must rise and fall steadily. If necessary, it must be securely sealed with ropes and chains. The fork must be carried out in strict accordance with the value specified in the vehicle load curve. Overloading is strictly prohibited
11. When the forklift is running, no one is allowed to get on or off the forklift, and no one is allowed to stand on the fork legs
12. When the factory forklift carries goods, the weight of the goods shall be shared equally between the two forklifts. The goods shall not be skewed, and one side of the goods shall be close to the shelf. Small items shall be put into the collection box (plate) to prevent falling. The forklift shall not block the sight of the driver https://ur8uz6.fanqier.cn/f/wdkk2d3x
13. In the plant area and construction site, the speed shall not exceed 10km per hour. The speed of entering and leaving the plant gate, workshop, warehouse and construction site shall not exceed 3kmh. Pay attention to braking when driving to prevent scratches and injuries
14. When lifting, lifting or driving a forklift in the factory, no one shall stand on the forklift to hold objects or maintain balance. When lifting forklift forks, no one is allowed to approach
15. When the forks approach or evacuate objects, the speed shall be slow and stable. Please note that the wheels should not crush objects, and the skids (trays) and fork heads should not scratch objects and support personnel
16. It is prohibited to use forklift and other accessories to lift personnel during high-altitude operation, electric forklift, single fork operation, forklift top and braking inertia sliding of dragging objects, circular or rolling objects, forklift and overturned pallet unloading. Do not fork objects at high speed
17. When the truck is inserted into the factory and the forklift lifts, the lifting frame shall tilt forward together with the ground, and the lifting frame shall not tilt forward.
18. When the forklift is parked in the plant, workshop and construction site, the driver shall not leave the vehicle. If you need to leave temporarily, you must remove the key and pull off the electrical switch
19. When the forklift stops the engine idling in the middle, the gantry shall tilt backward. When the engine is stopped, lower the lifting frame to make the fork level with the ground
20. It is not allowed to disassemble or assemble the goods directly at the quay or at the edge of the train carriage.
1. Before starting, observe the surrounding conditions of the forklift (for vehicles with air pressure or braking, the reading of the braking air pressure gauge must reach the specified value before starting), and whistle for starting after confirming that it is safe
2. Before driving, check the drivers license, drivers license and other documents required for driving. Driving without a license, driving without a license or driving without a license is strictly prohibited
3. Forklift drivers in the plant must strictly comply with the on-site traffic safety management standards and safety production specifications
4. Check the technical condition of each vehicle department according to the specified items and standards to make the forklift in good condition
5. Do not lift the fork too high when driving in the factory. When entering or leaving the operation site or driving, pay attention to whether there are obstacles in the air. Sudden braking and sharp turning prohibited
6. When the forklift is driving in the factory, the height from the fork bottom to the ground shall be kept at 300~400mm, and the gantry must tilt backward
7. Unless under special circumstances, the foot brake shall not be used when the forklift in the plant travels more than 7 ° and goes uphill and downhill at a speed higher than first gear 8. During loading and unloading, the forklift must be braked by the brake. If a crane is used to load and unload workpieces, the driver must leave the cab
9. After the forklift stops in the factory, it is forbidden to hang the goods in the air. After unloading, lower the lifting frame before driving
10. When the forklift is working in the factory, it must rise and fall steadily. If necessary, it must be securely sealed with ropes and chains. The fork must be carried out in strict accordance with the value specified in the vehicle load curve. Overloading is strictly prohibited
11. When the forklift is running, no one is allowed to get on or off the forklift, and no one is allowed to stand on the fork legs
12. When the factory forklift carries goods, the weight of the goods shall be shared equally between the two forklifts. The goods shall not be skewed, and one side of the goods shall be close to the shelf. Small items shall be put into the collection box (plate) to prevent falling. The forklift shall not block the sight of the driver https://ur8uz6.fanqier.cn/f/wdkk2d3x
13. In the plant area and construction site, the speed shall not exceed 10km per hour. The speed of entering and leaving the plant gate, workshop, warehouse and construction site shall not exceed 3kmh. Pay attention to braking when driving to prevent scratches and injuries
14. When lifting, lifting or driving a forklift in the factory, no one shall stand on the forklift to hold objects or maintain balance. When lifting forklift forks, no one is allowed to approach
15. When the forks approach or evacuate objects, the speed shall be slow and stable. Please note that the wheels should not crush objects, and the skids (trays) and fork heads should not scratch objects and support personnel
16. It is prohibited to use forklift and other accessories to lift personnel during high-altitude operation, electric forklift, single fork operation, forklift top and braking inertia sliding of dragging objects, circular or rolling objects, forklift and overturned pallet unloading. Do not fork objects at high speed
17. When the truck is inserted into the factory and the forklift lifts, the lifting frame shall tilt forward together with the ground, and the lifting frame shall not tilt forward.
18. When the forklift is parked in the plant, workshop and construction site, the driver shall not leave the vehicle. If you need to leave temporarily, you must remove the key and pull off the electrical switch
19. When the forklift stops the engine idling in the middle, the gantry shall tilt backward. When the engine is stopped, lower the lifting frame to make the fork level with the ground
20. It is not allowed to disassemble or assemble the goods directly at the quay or at the edge of the train carriage.
